Call Us: +92 51 11 11 BOSCH / Email: sales@theprotechtors.com

Bosch VIDEOJET connect 7000

2
  • Operates a variety of Bosch HD PTZ cameras, including MIC7000
  • Bi-directional audio, Alarms, washer pump control, local storage slot for a CompactFlash (CF) memory card, built-in web browser for control of connected cameras
  • One (1) HD-BaseT PoH dedicated for one RJ45 Ethernet port; three (3) RJ45 ports; two (2) SFP ports
  • Support for daisy-chaining of multiple cameras

The device VIDEOJET connect 7000 (VJC-7000-90) is a full-featured network power supply unit that can operate a variety of Bosch PTZ cameras such as MIC7000. The device includes one (1) HPoE network connection, two (2) standard network interfaces for connections to additional IP devices, one (1) slot for an optional CompactFlash (CF) memory card, two (2) slots for use with SFP-based fiber optic modules, alarm/washer control interfaces*, and audio I/O*. * Note: This feature is valid only for a MIC7000 camera “bound” to Camera 1.

VIDEOJET connect 7000

Electrical

Power requirements 100 VAC - 240 VAC (90 VAC - 264 VAC with tolerance considered), 50/60 Hz
Input power 94.3 W
Output power 82 W / 56V

Network

Communication 3x 10BASE-T/100BASE-TX/1000Base-TX If SFP fiber optic modules installed: 2x 1000 BASE-FX

SFP Modules

SFP (small formfactor pluggable) slot Two (2) for use with SFP-based fiber optic modules (1GB only) such as: • Agilent, SFP-GE-SX-MM850-A HFBR5710LP 7 • Cisco, GLC-LH-SM 1300nm • Cisco, GLC-SX-MM 850nm 8 • Finisar, FTLF8519P2BTL 850nm

Audio

Standard G.711, 8 kHz sampling rate L16, 16 kHz sampling rate AAC, 16 kHz sampling rate
Signal-to-Noise Ratio >50 dB
Audio Streaming Bidirectional (full-duplex)
connector 3.5 mm stereo jack
signal line in 9 kohm typical, 5.5 Vpp max
signal line out 3.0 Vpp at 10 kohm typical, 2.3 Vpp at 32 okhm typical, 1.7 Vpp at 16 ohm typical

Storage

Local storage One (1) slot for optional CompactFlash (CF) memory card, Type I / Type II, True IDE Mode, 1 TB max (usersupplied)

Miscellaneous

Washer switch Push button to activate/test the washer relay momentarily

User Connections

Alarm Inputs Four (4) normal dry contacts (selectable N.O./N.C.) Monitored supervised alarm input (Alarm 1), 2.2K ohm (Ω) end-of-line terminating resistor
Alarm Outputs Three (3) open collector outputs, 32 VDC, 150 mA
Washer driver output Dry contact relay, 250 V, 5 A
RJ45 connectors (3) – one PoE/PoH, 95W max; two standard network connections suitable for interface to head end network and ‘daisy chain’ type connection to second camera or VJC-7000-90 location

Environmental

Ingress Protection Rating/ Standard IP66, IP67, NEMA Type 4
Operating Temperature -40 °C to +60 °C (-40 °F to +140 °F)
Storage Temperature -60 °C to +70 °C (-76 °F to +158 °F)
Humidity 0–100%

Construction

Dimensions (L x W x H) 330 mm x 250 mm x 90.75 mm (13 in. x 9.84 in. x 3.57 in.)
Weight 7.21 kg (15.9 lb)
Material Powder-coated cast aluminum
Color White (RAL 9010) with sand finish
Standard Finish Powder coat paint, sand finish
Glands Water-tight glands/seals, rated IP67, NEMA Type 4

User Manual

Datasheet

Got any question or simply need help setting up something?

Head to our support forum

Support Forum

© Copyright 2015 The Protectors. All rights reserved.

Go to top: